Extended
SCPI Command :
CONFigure:BLUetooth:MEASurement<Instance>:MEValuation:LIST:SEGMent<nr>[:SETup]:EXTended
- class ExtendedCls[source]
Extended commands group definition. 1 total commands, 0 Subgroups, 1 group commands
- class ExtendedStruct[source]
Structure for setting input parameters. Contains optional setting parameters. Fields:
Burst_Type: enums.BurstType: BR | EDR | LE BR: ‘Basic Rate’ EDR: ‘Enhanced Data Rate’ LE: ‘Low Energy’
Phy: enums.LePhysicalTypeB: LE1M | LE2M | LELR LE1M: LE 1 Msymbol/s uncoded PHY LE2M: LE 2 Msymbol/s uncoded PHY LELR: LE 1 Msymbol/s long range (LE coded PHY)
Coding: enums.CodingScheme: S8 | S2 Coding S = 8 or S = 2 relevant only for LELR PHY Set dummy value for other physical layers.
Packet_Type: enums.SegmentPacketType: DH1 | DH3 | DH5 | E21P | E23P | E25P | E31P | E33P | E35P | RFPHytest | ADVertiser | RFCTe Packet type expected in the segment DH1, DH3, DH5: BR packet E21P, E23P, E25P, E31P, E33P, E35P: 2-DH1, 2-DH3, 2-DH5, 3-DH1, 3-DH3, 3-DH5 EDR packet RFPHytest: LE test packet ADVertiser: LE advertiser RFCTe: LE with CTE test packet
Pattern_Type: enums.MevPatternType: ALL1 | P11 | OTHer | ALTernating | P44 Payload pattern type expected in the segment ALL1: 11111111 P11: 10101010 OTHer: any pattern except P11, P44 and ALL1 ALTernating: the periodical change of the pattern P11, P44 P44: 11110000
Payload_Length: int: numeric Payload length expected in the segment Range: 0 Byte(s) to 1021 Byte(s)
No_Of_Off_Slots: int: numeric Number of unused slots between any two occupied slots or slot sequences expected in the segment. Range: 1 to 9
Segment_Length: int: numeric Number of measured bursts in the segment. The sum of the length of all active segments must not exceed 6700 timeslots (1 timeslot = 625 μs duration) . Range: 1 to 1000
Meas_On_Exception: bool: No parameter help available
Level: float: numeric Expected nominal power in the segment. The range of the expected nominal power can be calculated as follows: Range (Expected Nominal Power) = Range (Input Power) + External Attenuation - User Margin The input power range is stated in the data sheet.
Frequency: float: numeric Center frequency for the segment Range: 100 MHz to 6 GHz
Meas_Filter: enums.FilterWidth: NARRow | WIDE Filter bandwidth for the segment NARRow: narrow-band filter WIDE: wide-band filter
Retrigger: bool: OFF | ON Specifies whether a trigger event is required for the segment or not. The setting is ignored for the first segment of a measurement. OFF: measure the segment without retrigger ON: trigger event required
Cte_Units: int: Optional setting parameter. numeric No. of CTE units for LE with CTE, one unit corresponds to 8 μs. Range: 2 Byte(s) to 30 Byte(s)
Cte_Type: enums.CteType: Optional setting parameter. AOA | AOD1 | AOD2 CTE slot type for LE with CTE AOA: CTE type angle of arrival, 2 μs slot AOD1: CTE type angle of departure, 1 μs slot AOD2: CTE type angle of departure, 2 μs slot
- get(segment=Segment.Default) ExtendedStruct [source]
# SCPI: CONFigure:BLUetooth:MEASurement<Instance>:MEValuation:LIST:SEGMent<nr>[:SETup]:EXTended value: ExtendedStruct = driver.configure.multiEval.listPy.segment.setup.extended.get(segment = repcap.Segment.Default)
Defines the segment length, the signal properties including Bluetooth version 5.0 and higher, and the analyzer settings for a selected segment. In general, this command must be sent for all segments to be measured.
- param segment:
optional repeated capability selector. Default value: S1 (settable in the interface ‘Segment’)
- return:
structure: for return value, see the help for ExtendedStruct structure arguments.
- set(structure: ExtendedStruct, segment=Segment.Default) None [source]
# SCPI: CONFigure:BLUetooth:MEASurement<Instance>:MEValuation:LIST:SEGMent<nr>[:SETup]:EXTended structure = driver.configure.multiEval.listPy.segment.setup.extended.ExtendedStruct() structure.Burst_Type: enums.BurstType = enums.BurstType.BR structure.Phy: enums.LePhysicalTypeB = enums.LePhysicalTypeB.LE1M structure.Coding: enums.CodingScheme = enums.CodingScheme.S2 structure.Packet_Type: enums.SegmentPacketType = enums.SegmentPacketType.ADVertiser structure.Pattern_Type: enums.MevPatternType = enums.MevPatternType.ALL1 structure.Payload_Length: int = 1 structure.No_Of_Off_Slots: int = 1 structure.Segment_Length: int = 1 structure.Meas_On_Exception: bool = False structure.Level: float = 1.0 structure.Frequency: float = 1.0 structure.Meas_Filter: enums.FilterWidth = enums.FilterWidth.NARRow structure.Retrigger: bool = False structure.Cte_Units: int = 1 structure.Cte_Type: enums.CteType = enums.CteType.AOA driver.configure.multiEval.listPy.segment.setup.extended.set(structure, segment = repcap.Segment.Default)
Defines the segment length, the signal properties including Bluetooth version 5.0 and higher, and the analyzer settings for a selected segment. In general, this command must be sent for all segments to be measured.
- param structure:
for set value, see the help for ExtendedStruct structure arguments.
- param segment:
optional repeated capability selector. Default value: S1 (settable in the interface ‘Segment’)